davies auto care.inc Maintenance Tips: The Belt Goes On
Posted December 30, 2011 3:02 PM
Today's davies auto care.inc auto maintenance article focuses on your serpentine belt. Your serpentine belt is a long belt that’s driven by your engine. It winds around several accessories that power important automotive systems. Let’s go over them.
First, the serpentine belt drives your sedan air conditioning system. It spins the compressor that makes the cool air that takes the edge off the summer heat in palm springs.
Next, the belt powers the alternator. The alternator creates electricity that’s used by your sedan’s electrical systems and also charges your car battery. All palm springs drivers know that without the alternator, the battery will go dead in a few miles.
The serpentine belt may also run the pumps for both the power steering and power brakes. And, on many sedans, the serpentine belt powers the water pump. The water pump circulates coolant through the engine to keep it within normal operating temperatures as you drive around palm springs.
Now on some sedans, the water pump is powered by the timing belt instead of the serpentine belt. So you can see the serpentine belt does a lot of work. And it if breaks, it affects a lot of systems. That’s why manufacturers and your service advisor at davies auto care.inc have recommended that it be changed every so often so that it doesn’t fail. Your palm springs service technician can perform a visual inspection of the belt to see if it has any cracks that signal the belt could fail soon and will measure the amount of belt material to make sure there is enough.
There’s a special, spring loaded pulley attached to the engine called the tensioner pulley. Its job is to make sure there’s a constant tension on the serpentine belt so that it doesn’t slip. The spring can become worn and no longer provide the necessary pressure to keep the belt tight. At davies auto care.inc, we recommend that the tensioner be replaced at the same time as the serpentine belt. All in all, the serpentine belt’s an important part for the function of your sedan. And it’s not that expensive to replace in palm springs – so it’s good to do so before it fails.
Posted in the Maintenance category
Suspension Service At davies auto care.inc
Posted December 22, 2011 11:21 AM
Suspension systems will continue to operate effectively for many years and tens of thousands of miles. Eventually sedan components do wear out, but how long that takes depends a lot on how you drive in palm desert.
As you can imagine, if most of your driving is on smooth ca highways, your shock absorbers will last a lot longer than if you do most of your driving on bumpy roads or hauling heavy loads. In addition to just wearing out, sedan suspension components can be damaged in an accident or by a hard impact – like a pothole, hitting a curb or a rock in the road. Because the life span of shocks can vary so widely, your sedan manufacturer recommends periodic inspections.
During an inspection at davies auto care.inc, your honest,trustworthy,friendly palm desert service technician will check for worn, broken or missing parts. Let me give a rundown of the major suspension components.
First there are the springs. The springs hold the weight of the vehicle. There are several kinds of springs. Springs are obviously heavy duty parts that rarely break or wear out. Shock absorbers work in conjunction with springs to smooth out the ride and help keep the tires on the road. The shocks are key to handling performance and ride comfort.
You’ve probably heard of struts. They combine a shock absorber and a coil spring in one unit. Shocks and struts will wear out over time. There are some signs that shocks or struts are wearing out. The tires may have a cupped wear pattern. This is from the shocks bouncing unevenly. You may notice a floaty or drifting sensation when cornering. If the front of your sedan dives excessively when stopping, or rocks back and forth after you stopped, your shocks may be worn out. And if they are leaking fluid, it’s definitely time to replace them.
If you are experiencing any of these symptoms, visit davies auto care.inc for a suspension inspection. Same if you’ve been in an accident that involved one of your wheels. If your sedan suspension actually fails, it could lead to a serious accident, so take care of these things.
When you replace your shocks, it’s usually a good idea to replace all four at the same time. That’ll give you more even handling. Talk with your davies auto care.inc service advisor because you don’t want a big difference between the performance of your shocks from wheel to wheel, and replacing all may be the safest bet.
There different grades of shocks and struts. You always want to use a replacement shock or strut that equals the one that came as original equipment when your sedan was new. But remember, they were designed to meet the expected needs of the broad range of palm desert people who buy that particular vehicle. Your needs may be more specialized.
For example if you want increased handling performance for your sedan, your honest,trustworthy,friendly davies auto care.inc advisor can recommend an upgraded shock or strut to give you what you want. If you haul heavy loads or trailers, you can get a more heavy duty shock absorber.
Posted in the Shocks & Struts category
davies auto care.inc Tire Safety: Washington vs. Lincoln
Posted December 14, 2011 9:30 AM
Welcome to the davies auto care.inc blog. Today, let’s talk about the effect of tire tread depth on braking. When talking about stopping power, most of us indio drivers tend to focus on our brakes. But our tires are where the rubber meets the road. So having good brakes isn’t enough. Safe indio drivers need to have tires with enough traction to translate braking power into stopping power.
Let’s focus on stopping in wet indio conditions. In order for a tire to have good contact with the road, it has to move the water out of the way. If it can’t move the water, the tire will actually ride on top of a thin film of water.
That’s called hydroplaning. If it’s really bad, indio drivers can actually spin out of control. At best, you won’t stop as fast.
So how does a tire move water? It has channels for water to flow through. Look at your sedan tire and you’ll see channels: channels that run around the tire and channels that flow across the tire. They’re designed to direct water away from the tire so it can contact the road better.
And the deeper the channel, the more water it can move. A brand new davies auto care.inc tire has very deep channels and can easily move a lot of water. As the tire wears down, the channels become shallower and can move less water. When it wears down enough, it can seriously affect your ability to stop your sedan on wet indio roads.
So that’s why it’s so important to replace our sedan tires when they get worn. Consumer Reports and other advocate groups call for a standard of 3/32 of an inch and they have the studies to prove it.
By comparison, you’ve probably seen the wear indicator that’s molded into tires. When tires are worn 3/32 of an inch, the tread wear bar is visible. So the recommended standard has twice the tread depth as a completely worn out sedan tire.
At davies auto care.inc, we want our customers to know that the deeper recommended tread depth makes a big difference. Stopping distances are cut dramatically on wet indio roads. A safe stop from ca freeway speeds with 4/32 of an inch of tread would result in a crash with worn out tires.
There’s an easy way to tell when a tire’s worn to 4/32 of an inch. Just insert a quarter into the tread. Put it in upside down. If the tread doesn’t cover George Washington’s hairline, it’s time to replace your sedan tires. With a Canadian quarter, the tread should cover the numbers in the year stamp.
Many indio car owners have heard of this technique using a penny and Abe Lincoln’s head. That measure gives you 2/32 of an inch – half the suggested amount. Of course, sedan tires are a big ticket item. Most of us in indio want to get as many miles out of them as we can. But there’s a real safety trade-off. It’s your choice.
Posted in the Tires and Wheels category
PCV Valve Service At davies auto care.inc In cathedral city
Posted December 6, 2011 11:52 AM
The PCV Valve is a little, inexpensive part that does a big job for cathedral city drivers. PCV stands for Positive Crankcase Ventilation.
The crankcase is the bottom area of the engine that holds the oil. When the sedan engine’s running, fuel is burned to generate power. Most of the exhaust from combustion goes out through the exhaust system. But some exhaust blows by the pistons and goes into the lower engine, or crankcase. These hot gases are about seventy percent unburned fuel.This can dilute and contaminate the oil, leading to damaging engine oil sludge. It can also cause sedan engine corrosion, something we see occasionally at davies auto care.inc. At high speeds on cathedral city freeways, the pressure can build up to the point that gaskets and seals start to leak.
Back in the old days, engine makers simply installed a hose that vented these gases out into the atmosphere. But starting in the 1964 model year, laws mandated that these gases be recycled back into the air intake system to be mixed with fuel and burned in the sedan's engine.
This is much better for the environment and it saves gas too. (Budget-conscious cathedral city drivers take note!) The little valve that controls all this action is the PCV valve. The PCV valve lets gases out of the engine, but won’t let anything back in. Over time, the vented gases will gum up the PCV valve and it won’t work well. That can lead to all of the problems I’ve already described, oil leaks, excessive oil consumption and wasted gas.
Fortunately, it’s very easy to test the PCV Valve at davies auto care.inc and quick and inexpensive to replace. Even so, it’s often overlooked because many cathedral city drivers don’t know about it. Check your sedan owner’s manual or ask your davies auto care.inc service advisor. If this is the first time you’ve heard of a PCV valve, you might be in line for a replacement.
There’s another aspect to the PCV system. In order for the valve to work correctly, it needs a little clean air to come in. This is done through a breather tube that gets some filtered air from the engine air filter. Now some vehicles have a small separate air filter for the breather tube called the breather element. That’ll need to be replaced at davies auto care.inc when it gets dirty.
Please ask your honest,trustworthy,friendly cathedral city service advisor about your PCV valve. For the price of a couple of burger combo meals in cathedral city, you can avoid some very expensive deep engine repairs.
Posted in the Parts category
davies auto care.inc Radiator Service
Posted December 1, 2011 12:20 PM
The coolant system is a vital part of your vehicle. It is also the second most common cause for vehicle failures. Even though coolant system failure is fairly common, it is easy to prevent.
The most recognizable part of the coolant system is the radiator. It is connected to the engine with hoses and is filled with coolant. The coolant draws heat off the engine and then goes into the radiator. Air passes through cooling fins to reduce the temperature of the coolant and then it's back to the engine again.
There are several ways for the cooling system to fail. Most common is with the coolant itself. Coolant is a mixture of water and antifreeze. The proper mixture keeps the coolant from either boiling away or freezing. Both of which can result in massive engine damage.
Another very important coolant issue that is often overlooked is the age of the coolant itself. Antifreeze has additives that protect the coolant system from corrosion. As these additives are depleted over time, they can't protect the radiator and other parts from rust, scaling and corrosion. Old coolant may still keep your engine cool, but it won't protect it from corrosion.
If you see a warning message to check the coolant or if the temperature gauge is in the hot zone your cooling system needs to be checked. It's OK to add water or antifreeze yourself. But you need to be cautious. Remember four things.
First, you never want to open the radiator pressure cap. You could be severely burned.
Second, try to get to your cathedral city service center at davies auto care.inc immediately if your coolant is low. If that is not possible, follow the directions in your owners manual - it will direct you to only make additions to the coolant overflow bottle.
Third, remember that you need a proper mixture of water and antifreeze. If you make an emergency addition to your cooling system, follow-up with your davies auto care.inc service center where we can make necessary corrections.
Fourth, not all cars use the same type of antifreeze. You need to check your owners manual to make sure you use the right kind. Mixing antifreeze types or using the wrong kind of antifreeze may void the manufacturers warranty on your cooling system. Again, another reason to rely on your davies auto care.inc service center in cathedral city to do things right.
Remember, your cathedral city service center has the equipment to change your coolant quickly and inexpensively.
Posted in the Cooling System category
Suspension Service In cathedral city ca
Posted December 1, 2011 12:20 PM
When you hear the word 'suspension', you may think back to those energetic days of grade school. Well, your car’s suspension is actually a good thing because it keeps your car up off the road and helps provide a comfy ride. It needs to keep your wheels firmly planted over bumps and through curves. Your suspension system has many parts. If you look under your car, it’s basically everything that connects your wheels to the car’s frame. These are heavy duty parts that do a lot of work. They need to be inspected for damage and excessive wear at least once a year. A good time for this is when you get your annual alignment service.
Here are some warning signs that your suspension may have problems:
the car pulls to one side;
it wanders;
the steering is erratic;
you see uneven tire wear;
you experience a poor ride or handling;
you see oil leaking from shocks
. . . You just don’t feel in control when you’re driving.
Some suspension parts just wear out with use. Shocks and struts eventually lose their ability to control your ride. Wheel bearings need to be repacked every couple of years. And some suspension pieces need to be lubricated when you get your oil changed. Your service advisor at davies auto care.inc can oversee an inspection and tell you what problems you may have.
If you’re in an accident, your suspension can be damaged or knocked out of alignment. Even a minor accident, like hitting a curb around cathedral city or even a large rock can mess things up. With a minor accident it’s tempting to just get an alignment or wheel balance to correct the problem. But if there’s some damage, a simple alignment won’t actually fix the problem, and you’ll just have to align it again after the repairs are made. So if you have an accident, get your suspension system inspected right away. Suspension problems should be fixed immediately because they can lead to unsafe handling.
One big cause of suspension damage is potholes – those nasty magnets that seem to draw our tires right into them. Well, Here are some tips for avoiding damage from potholes: First, keep your tires at their full air pressure. That gives tires their maximum resiliency and will hopefully keep your wheels or other suspension parts from crunching on a big hole. Next, just pay attention. When you see a hole you can’t miss, slow down before you hit it. Driving at a slower speed will limit the damage, and may keep your drink from spilling. But don’t brake directly over the pothole. That will cause the car’s weight to shift forward and add to the potential damage.
davies auto care.inc Give us a call today at (760)328-6198. Or stop by at 68300 perez rd, cathedral city, ca 92234
Posted in the Shocks & Struts category
Exhaust Service
Posted December 1, 2011 12:16 PM
Whenever we talk about exhaust service, most people normally think about exhaust pipes and mufflers. Well, actually, exhaust service is a lot more comprehensive these days. For example, catalytic converters were mandated in 1976 and on-board emission control computers in 1990. Governmental emissions requirements have forced manufacturers to come up with much more sophisticated ways to comply with environmental regulations.
Exhaust service has really become exhaust and emissions service. High-tech computer controlled emissions devices are now a big part of exhaust service. Because it is so sophisticated, your vehicle manufacturer recommends you have your emission system checked out by a qualified cathedral city exhaust technician regularly to make sure everything is working right - usually every 6 months or 10,000 miles/16,000 kilometers.
If your Check Engine light comes on, especially if it's flashing, get your car looked at right away. Technicians at davies auto care.inc handle emission problems everyday. You might have exhaust or emissions trouble if your car is difficult to start, runs rough, is noisy or smoking. Call davies auto care.inc at (760)328-6198 to schedule an appointment if you experience these problems.
Let's review the exhaust system. We will start from the top and start with the exhaust manifold. That is the part that attaches to the engine and collects the exhaust from the cylinders and directs it into the exhaust pipe. Exhaust gaskets help seal the connection with the manifold and various other joints along the way. If the manifold is cracked or loose, or a gasket is leaking, dangerous gases could escape into the passenger compartment, where you ride. Carbon monoxide can be deadly, so it is important that your exhaust system doesn't leak. The exhaust pipes connect the various components. They can rust or be damaged by a rock, so they need to be inspected periodically.
Next is the catalytic converter. This part looks like a muffler. It changes chemicals that are dangerous to your health and the environment into harmless carbon dioxide and water. It doesn't require any maintenance itself. But eventually they wear out. You will find this out when your car fails an emissions inspection.
Now the muffler. Its main job is to quiet engine noises. Mufflers work by either absorbing or baffling sound. And you can actually customize your car's sound with different mufflers - anything from whisper quiet to bad-boy rumbley. Rusted or road-damaged mufflers can leak and need to be replaced right away.
The exhaust system is attached to the car by a series of hangers and clamps. These fasteners hold the system in place. When hangers come loose or break, hot exhaust components can touch and melt wires, hoses and lines.
Finally, we end at the tailpipe. This is the final outlet for the exhaust. These can be plain-Jane or pretty flashy. Also, the oxygen sensors monitor the oxygen content of the exhaust so the engine control computer can adjust the fuel-to-air mix to keep the car running right.
Exhaust and emissions service covers plain old pipes and high-tech computers. It impacts everything from life and death safety due to exhaust leaks, to fine-tuning the sound of your ride.
Posted in the Exhaust category
Differential Service
Posted December 1, 2011 12:09 PM
Here at AutoNetTV, we have viewers, like you, from all across the country who write to us with questions or feedback. One common question we're asked is: What is a differential and what does it do? You may have been told your differential needs service, or seen it as an option up on the service menu. Differential service covers a lot of things, so let's first talk about what a differential does.
As you drive through a turn, your outside wheels and inside wheels turn at different speeds. Kind of like the cars going around a race track - the ones driving in the outside lanes have a greater distance to travel than the cars in the inside lanes. The differential is what allows the outside and inside drive wheels to rotate at slightly different speeds so that the tires don't hop or skip while taking corners, or lose traction in dirt or snow. Differentials have gears in them that transfer the power from the drive train to your wheels - which is why they're often referred to as gear boxes. The gears need to be very strong to do this work, and they need to be properly protected so that they'll last.
All vehicles have some form of differential. If you have a front-wheel drive car, your differential is often called a transaxle and is located in the front. If you have rear-wheel drive, the differential is in the back of the car. If you have a four-wheel drive vehicle, you will have a differential in the front and the back - and in the middle as well. The center differential adjusts for differences in speed between the front and rear wheels.
Differential fluid lubricates and cools the gears. Over time, the fluid can get dirty from bits of the gears grinding off. The additives that keep the fluid clean and protect the differential break down over time. So your vehicle manufacturer has scheduled intervals for you to have your differential fluid changed.
Differentials are hard working mechanisms, and, along with the gears in a manual transmission, need to be serviced regularly with high-quality, replacement fluid. Your palm springs automotive service advisor can give you more information as to when your next differential service is recommended. You can also ask if they have a record of when the service was last completed.
As with most service intervals, if you are driving under more severe conditions, you will want to service your differential more frequently. "Severe service" conditions are defined in most owners' manuals, and include: frequent starts and stops, short trips, cold weather, hot weather and towing. All these conditions add to the stress of the vehicle and its parts. Also, off-roading in ca can be especially hard on differentials, especially if you cross streams. Proper service will extend the life of your gears and keep them running more smoothly. If you have never had your differential checked, visit davies auotcare for more information.
Posted in the Drive Train category
What To Do After You Buy a Used Vehicle in cathedral city
Posted December 1, 2011 12:08 PM
So you’ve bought a used car in the cathedral city area. How do you know what you’re getting? It is hard to know what you’re getting because people in the cathedral city area sell cars for different reasons. Think about why you’ve sold cars. Did you just want something new or were there problems that you wanted to run away from. Maybe it was a little of both.
Used cars with 25,000 to 35,000 miles on them are often lease returns, corporate program cars or vehicles that have done duty in rental fleets. We feel pretty confident because they’re newer and may still be under warranty. But how well have they been maintained?
If you plan on owning a car for a long time, you’ll keep up on the maintenance so that you can avoid expensive repairs down the road. But, if you know you’re only going to have the car for two or three years, you may not be so committed to maintenance. It would be easy to think that skipping an oil change here and there wouldn’t ruin a brand new engine. Then it’ll be someone else’s problem when it comes time to pay for the damage.
It would be very tempting to skip the 30,000 mile service if you knew you’d be turning in your leased vehicle in a couple of months.
If the vehicle didn’t come with maintenance records, you need to assume the worst. Most likely the coolant system and transmission have never been serviced. The cabin air filter has probably not been changed and a fuel system cleaning may be in order.
And if your “new” used vehicle has more miles on it, an inspection is even more important. Check your owner’s manual or talk with your service advisor at davies auto care.inc (call (760)328-6198) about what should have been done. Please don’t forget the timing belt; that can be very expensive if it fails.
davies auto care.inc will help you with a plan to take care of critical services and get the rest caught up. If your budget won’t allow you to take care of everything right away, we can help you prioritize your needs and get it taken care of over the next several months. And remember to keep your maintenance records. They’ll help you get top dollar when it’s time for you to sell.
What type of technology do you use? Do you prefer an 8-track tape or an iPod? When it comes to winter tires, much of the public's perception dates back to when 8-track was the best way to listen to the Bee Gees.
Twenty years ago, winter tires differed from highway tires only in their tread design. We called them snow tires back then and they had big, knobby lugs that were designed to give good traction in deep snow. They had the same rubber compound as regular tires and they weren't very good on ice, packed snow or wet roads. They were not even very good on dry roads. They really helped in deep or loose snow, but they did a poor job the rest of the time. They were loud and rode hard. You couldn't wait to get them off in the spring.
Then all-season tires started to come along. All-season tires are really a compromise between summer and winter performance. They have acceptable hot weather ride and tread life, and you can get through mild winter road conditions OK. But there are some really good reasons to consider winter tires.
Modern winter tires do a terrific job in a wide range of winter conditions. First of all, below 45 degrees Fahrenheit, regular tires become hard and inflexible. That means they don't provide the road grip you need. Even if you don't live somewhere with a lot of snow, but it still gets below 45 degrees in the winter, you will be safer with winter tires.
In addition, they are specifically designed to more effectively move snow and water. That's the key to traction on ice, packed snow and wet roads. They use a micro-pore compound that allows the tire to bite into ice and snow. They also use wider grooves that run around the circumference of the tread to expel snow from the tire better. The lugs and grooves on winter tires have a special shape that throws the packed snow out of the tread as the tire turns. The tread is then open when it comes back in contact with the road and can provide good traction.
Winter tires also have a lot of sipes. Sipes are thin slits in the tread. The edge of the sipes grab ice and packed snow to provide tons of traction and to expel water and slush out of the tread. winter tires have a rounder casing to cut into the snow's surface. The treads on regular summer tires can actually get packed with snow instead and become very slick. winter tires offer 25% to 50% more traction than all-season tires. And when it comes to stopping power, all-season tires take 42% longer to stop than winter tires. Sometimes that's the difference between getting home safely and spending the night in a snow bank.
Now back when the 8-track was king, you just put snow tires on the drive wheels. That worked out OK because the rubber compound was essentially the same. Now, winter tires provide so much more traction than all-season or summer tires, that there's a huge difference between the traction at the front and rear ends of the car if you only put winter tires on the drive wheels.
For example: if you take a corner on an icy road and the rear end starts to slide out, essentially the rear is trying to pass the front because it's going faster. If you have high traction winter tires only on the front, they are going to be much more effective at transferring cornering grip and stopping power to the front wheels. This will actually cause the rear end to whip out even more.
That's why tire manufactures instruct their dealers that they must install winter tires on the rear wheels as well whenever they put winter tires on the front end of any vehicle. It's a major safety concern. It's strongly recommended that winter tires be installed on all four wheels on rear wheel drive vehicles as well. The front tires do most of the steering and braking work - it only makes sense that you provide the front end with the best traction you can.
People often assume that if they have four-wheel drive or all-wheel drive they don't need winter tires on all four wheels. Would you intentionally disconnect the four-wheel drive in poor road conditions? Of course you wouldn't, but that's essentially what you do if you only put winter tires on one end. It only makes sense to have the same level of traction and control at all four corners.
The province of Quebec in Canada has issued a law requiring all passenger vehicles, taxis and rental cars with Quebec license plates to install a full set of four winter tires between November 15th and April 1. It's that important.
Many modern cars have traction control and anti-lock brakes so people may think that they don't need winter tires. But you need traction to accelerate, steer and stop. The tires provide the traction so that the traction control and anti-lock brakes have something to work with.
Look for tires with the symbol of a mountain with a snowflake in it. This means the tire complies with the severe snow standard. All-season tires will have an M&S, for mud and snow, on the sidewall.
So when the temperatures drop below 45 degrees, be sure you have a set of four winter tires for maximum performance in snow, packed snow, ice, wet and dry roads. Your tire professional can help you find the right winter tire for your vehicle and driving needs.